Heading "Water Supply"
Why is a well piping needed and how is it performed
Why is a well piping needed and how is it performed
Tying the well involves laying a pipeline, installing pumping equipment and filters, protecting the casing from freezing. Preliminary, you should draw up a project so as not to miss anything. The climate, source characteristics and location of the outlets should be considered.
Why in the spring the water in the well became muddy and what to do about it
Why in the spring the water in the well became muddy and what to do about it
The main causes of clouding of water in the well: violation of the tightness of the walls, the ingress of domestic or industrial effluents into the aquifer, stagnation of water, improper installation of a submersible pump. It is necessary to pump out all the water from the structure, clean and grease the walls, install a bottom filter.
How to install and connect a pumping station to a well
How to install and connect a pumping station to a well
A pumping station for a well consists of a pumping unit, a hydraulic accumulator, and a pressure switch. The pump may be surface or submersible. When choosing a model, it is necessary to take into account the performance of the installation and the source, the location of the water folding units relative to the well, the required volume of water.
What are the filters for hard water and how to choose the right model
What are the filters for hard water and how to choose the right model
Filters for hard water remove alkali, calcium, salt, iron compounds. As a result, the water becomes soft, does not have a harmful effect on the body and does not provoke rapid wear of household appliances. There are many devices on the market of different price categories, differing in design and principle of operation.
What to choose as a source of water for a private house and cottage: a well or a well
What to choose as a source of water for a private house and cottage: a well or a well
When choosing between a well and a well on a site, one must rely on the requirements for water quality, volume and purpose of application. A well or an Abyssinian well with a depth of 10-12 meters is enough for a summer cottage. For year-round supply of clean water at home, it is better to drill a well on sand or an artesian spring.
What is the purpose of installing a water pressure switch for a borehole pump and how it works
What is the purpose of installing a water pressure switch for a borehole pump and how it works
Setting the pressure switch for the downhole pump is necessary for optimal water pressure in the system and for adjusting equipment on / off cycles. The device saves electricity and extends the life of the accumulator membrane.
In what situations may it be necessary to pump water from a well and how to do it
In what situations may it be necessary to pump water from a well and how to do it
Pumping water from the well is necessary when it is contaminated with groundwater, melt, rain, domestic sewage. You can use buckets and scoop up liquid by hand, but this is a long and laborious process. It is better to use one or two pumps.
Why did the water in the well turn yellow and how to deal with it
Why did the water in the well turn yellow and how to deal with it
Yellow water in the well may indicate a source depressurization, industrial, domestic wastewater or other pollution entering the aquifer. It is necessary to make a laboratory analysis and identify the cause of the decrease in fluid quality.
What is a hydraulic accumulator membrane?
What is a hydraulic accumulator membrane?
The membrane for the accumulator serves as a water storage. Gas or air from the housing puts pressure on it. When the crane is turned on, the pear is emptied, the pressure drops, the pump turns on and replenishes the fluid reserves. Membranes can be removable and stationary.
Overview of Reflex Accumulators for Water Systems
Overview of Reflex Accumulators for Water Systems
German manufacturer’s Reflex accumulators are made of carbon steel and coated with enamel inside to protect against moisture.The membrane is made of butyl rubber rubber designed to store drinking water. The lineup is represented by products with a removable and fixed pear.
How to check the accumulator for operability and eliminate breakdowns
How to check the accumulator for operability and eliminate breakdowns
The maintenance of the accumulator consists in periodically checking its tightness, pressure inside the housing, and the integrity of the membrane. Most components are easy to replace with your own hands, the main thing is to do it in a timely manner.

Heating

Ventilation

Sewerage